====== MP-11X FXO ======
MP-11x Analog VoIP Gateways based on version 6.6.

This document covers the specific settings for the DV2000 connected to the Avaya S8300. AudioCodes provides many pre-built configuration files for many PBX's and documentation to match [[https://www.audiocodes.com/library/technical-documents?query=MediaPack&productGroup=1691|here]].

===== Requirements =====
  * DuVoice DV2000 7.2.26 or above.
  * DV2000 licensed for SIP.

====== Configuration ======

===== DV2000 =====

==== Setup Wizard ====
  * **PBX Model** - Other > SIP Gateway.
  * **Message Waiting (MWI)** - SIP Notify

==== PBX Settings ====
{{:images:integration:audiocodes:mp11x:pbxsettings.png?direct|}}
  * **IP or DNS Name** \\ Enter the IP address of the AudioCodes gateway.
  * **Call Progress** \\ Choose //Audio tones after RING event//.

==== Lines ====
{{:images:integration:audiocodes:mp11x:linesettings.png?direct|}}
  * Enter the extension numbers associated with the PBX.
  * Leave all other settings as shown.

==== MWI Template ON/OFF ====
{{:images:integration:audiocodes:mp11x:mwisettings.png?direct|}}
  * **Method** \\ SIP.

===== AudioCodes =====
  * Default username: **Admin**.
  * Default password: **Admin**.
  * Settings will take effect when Submit is pressed but will not be retained on power loss unless **Burn** is pressed.
  * We have found difficulty programming the AudioCodes using firefox browser. Chrome or Edge seem to work fine.
  * Some features listed may only available when viewing **Full** rather than **Basic**.
  * Disconnect parameters may need to be adjusted based for your PBX.

==== Media ====
=== Voice Settings ===
Default settings shown for reference.
{{:images:integration:audiocodes:mp11x:103-1.png?direct|}}

=== Fax/Modem/CID Settings ===
{{:images:integration:audiocodes:mp11x:103-2.png?direct|}}
  * **CNG Detector Mode** \\ Events Only.

==== Control Network ====
=== Proxy Sets Table ===
{{:images:integration:audiocodes:mp11x:106-2.png?direct|}}
  * **Proxy Address** \\ Enter the IP address of the DV2000.
  * **Transport Type** \\ Enter UDP.

==== SIP Definitions ====
=== General Parameters ===
{{:images:integration:audiocodes:mp11x:107-1.png?direct|}}
  * **Channel Select Mode** \\ Descending or Ascending.

=== Advanced Parameters ===
{{:images:integration:audiocodes:mp11x:107-2.png?direct|}}
  * **Disconnect on Broken Connection** \\ No.
  * **CDR Report Level** \\ None or End Call.

=== Proxy & Registration ===
{{:images:integration:audiocodes:mp11x:107-4.png?direct|}}
  * **Use Default Proxy** \\ Yes.
  * **Subscription Mode** \\ Per Gateway.

==== Coders and Profiles ====
=== Coders ===
{{:images:integration:audiocodes:mp11x:108-1.png?direct|}}
  * Set Coders as shown.

=== Tel Profile Settings ===
Default settings shown for reference.
{{:images:integration:audiocodes:mp11x:108-3.png?direct|}}
  - **Dialing Mode** \\ One Stage.

=== IP Profile Settings ===
{{:images:integration:audiocodes:mp11x:108-4.png?direct|}}
  * **Disconnect on Broken Connection** \\ No.
  * **Play Ringback Tone to IP** \\ Yes.

==== GW and IP to IP ====
=== Hunt Group > Endpoint Phone Number Table ===
{{:images:integration:audiocodes:mp11x:109-1-1.png?direct|}}
  * **Channel(s)** \\ Enter line number.
  * **Phone Number** \\ Enter the extension assigned to the DV2000.

=== Manipulations > Dest Number Tel->IP ===
{{:images:integration:audiocodes:mp11x:109-1-2-3.png?direct|}}
  * **Destination Prefix** \\ *
  * **Source Prefix** \\ *
  * **Source Trunk Group ** \\ -1
  * **Destination IP Group** \\ -1

=== Routing > Routing General Params ===
Default settings shown for reference.
{{:images:integration:audiocodes:mp11x:109-3-1.png?direct|}}

=== Routing > Tel to IP Routing ===
{{:images:integration:audiocodes:mp11x:109-3-2.png?direct|}}
Setting the following and pressing //Submit// will set all other fields to correct settings.
  - **Dest. IP Address** \\ IP address of DV2000.
  - **Port** \\ 5060
  - **Transport Type** \\ UDP

=== DTMF and Supplementary > DTMF & Dialing ===
{{:images:integration:audiocodes:mp11x:109-4-1.png?direct|}}
  - **Max Digits In Phone Num** \\ Enter a minimum of 15. This number must be the maximum number of INBAND digits expected. Consider calls from external numbers as well. A greater value will not cause any issues other than a small delay.
  - **RFC 2833 Payload Type** \\ 101.
  - **Enable Special Digits** \\ Enable. Inband integration will not function unless enabled because it will stop on the first non-numeric DTMF.
  - **Default Destination Number** \\ Enter the first extension number of the DV2000 or the huntgroup assigned.

=== DTMF and Supplementary > Supplementary Services ===
{{:images:integration:audiocodes:mp11x:109-4-2.png?direct|}}
  - **Enable MWI** \\ Enable.

=== Analog Gateway > FXO Settings ===
{{:images:integration:audiocodes:mp11x:109-5-1.png?direct|}}
  - **Dialing Mode** \\ One Stage.
  - **Answer Supervision** \\ No.

=== Advanced Applications > Voice Mail Settings ===
{{:images:integration:audiocodes:mp11x:109-6-1.png?direct|}}
  - **Line Transfer Mode** \\ Blind.
  - **Voice Mail Interface** \\ DTMF.

<WRAP center round important 100%>
Ensure the **Digit Patterns** and **Message Waiting Indication (MWI)** codes match your PBX.
</WRAP>

<WRAP center round alert 100%>
In some instances the gateway may not hear the first DTMF or the INBAND integration. In this case simply remove the first digit for each entry and a match should be found. This has been seen specifically on the Avaya Partner.
</WRAP>


===== Addendum =====

==== Reset to Defaults ====
The AudioCodes can be defaulted in two ways. While the manual details this is performed via the reset button, this will cause all network settings to be reset as well.

An easier way which retains the network settings, yet defaults all others is to upload a blank .ini file to the gateway. Using notepad or other text editor, create a file and name it empty.ini with nothing in it and upload it.

==== Logging ====
The AudioCodes logging is really only visible via a SysLog application. AudioCodes provides one [[https://tools.audiocodes.com/install/|here]] or search for //audiocodes utilities// in your favorite search engine. Ensure that logging is disabled once any testing has been completed. Installing this utility on the DV2000 will not impact the system.

{{:images:integration:audiocodes:mp11x:syslog-settings.png?direct|}}
  - **Enable Syslog** \\ Enable, change back to Disable when testing is completed.
  - **Syslog Server IP Address** \\ Enter the IP address where the syslog software is installed. 

==== Configuration ====
Configuration file matching the above text which can be loaded.

<file dv-audiocodes.ini>
;**************
;** Ini File **
;**************

[SYSTEM Params]

SyslogServerIP = 0.0.0.0
;VpFileLastUpdateTime is hidden but has non-default value

[BSP Params]

PCMLawSelect = 3
DHCPEnable = 1
RoutingTableHopsCountColumn = 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

[Analog Params]

CurrentDisconnectDuration = 450

[ControlProtocols Params]


[MGCP Params]


[MEGACO Params]

EP_Num_0 = 0
EP_Num_1 = 1
EP_Num_2 = 0
EP_Num_3 = 0
EP_Num_4 = 0
;3LevelNamingBChannelStartNum is hidden but has non-default value

[Voice Engine Params]

CallProgressTonesFilename = 'usa_tones_13.dat'
IdlePCMPattern = 85
ECNLPMode = 1
CNGDetectorMode = 2
RFC2833TxPayloadType = 101

[WEB Params]

LogoWidth = '208'

[SIP Params]

MAXDIGITS = 15
TIMEBETWEENDIGITS = 2
;ISUSEFREECHANNEL is hidden but has non-default value
ISSPECIALDIGITS = 1
ISPROXYUSED = 1
ISTWOSTAGEDIAL = 0
ENABLECURRENTDISCONNECT = 1
CDRREPORTLEVEL = 1
;ENABLECDR is hidden but has non-default value
CHANNELSELECTMODE = 2
GWDEBUGLEVEL = 5
;ISPRACKREQUIRED is hidden but has non-default value
ENABLEVOICEDETECTION = 0
DISCONNECTONBROKENCONNECTION = 0
ENABLEMWI = 1
LineTransferMode = 1
VoiceMailInterface = 1
DigitPatternForwardNoReason = '#02#S.#R.#'
DigitPatternForwardOnBusy = '#02#S.#R.#'
DigitPatternForwardOnNoAnswer = '#02#S.#R.#'
DigitPatternForwardOnDND = '#03##R.#'
DigitPatternInternalCall = '#00#S.##'
DigitPatternExternalCall = '#01#S.##'
MWIOnCode = '*2'
MWIOffCode = '#2'
SUBSCRIPTIONMODE = 1
SIPTRANSPORTTYPE = 1
MSLDAPPRIMARYKEY = 'telephoneNumber'

[IPsec Params]


[SNMP Params]


[ DspTemplates ]

;
;  *** TABLE DspTemplates *** 
; This table contains hidden elements and will not be exposed.
; This table exists on board and will be saved during restarts.
;

[ \DspTemplates ]


[ PREFIX ]

FORMAT PREFIX_Index = PREFIX_DestinationPrefix, PREFIX_DestAddress, PREFIX_SourcePrefix, PREFIX_ProfileId, PREFIX_MeteringCode, PREFIX_DestPort, PREFIX_SrcIPGroupID, PREFIX_DestHostPrefix, PREFIX_DestIPGroupID, PREFIX_SrcHostPrefix, PREFIX_TransportType, PREFIX_SrcTrunkGroupID, PREFIX_DestSRD, PREFIX_CostGroup, PREFIX_ForkingGroup, PREFIX_CallSetupRulesSetId;
PREFIX 0 = "*", "192.168.100.100", "*", 0, 255, 5060, -1, "", -1, "", 0, -1, -1, "", -1, -1;

[ \PREFIX ]


[ NumberMapTel2Ip ]

FORMAT NumberMapTel2Ip_Index = NumberMapTel2Ip_DestinationPrefix, NumberMapTel2Ip_SourcePrefix, NumberMapTel2Ip_NumberType, NumberMapTel2Ip_NumberPlan, NumberMapTel2Ip_RemoveFromLeft, NumberMapTel2Ip_RemoveFromRight, NumberMapTel2Ip_LeaveFromRight, NumberMapTel2Ip_Prefix2Add, NumberMapTel2Ip_Suffix2Add, NumberMapTel2Ip_IsPresentationRestricted, NumberMapTel2Ip_SrcTrunkGroupID, NumberMapTel2Ip_SrcIPGroupID, NumberMapTel2Ip_DestIPGroupID;
NumberMapTel2Ip 0 = "*", "*", 255, 255, 0, 0, 0, "", "", 255, -1, -1, -1;

[ \NumberMapTel2Ip ]


[ IpProfile ]

FORMAT IpProfile_Index = IpProfile_ProfileName, IpProfile_IpPreference, IpProfile_CodersGroupID, IpProfile_IsFaxUsed, IpProfile_JitterBufMinDelay, IpProfile_JitterBufOptFactor, IpProfile_IPDiffServ, IpProfile_SigIPDiffServ, IpProfile_SCE, IpProfile_RTPRedundancyDepth, IpProfile_RemoteBaseUDPPort, IpProfile_CNGmode, IpProfile_VxxTransportType, IpProfile_NSEMode, IpProfile_IsDTMFUsed, IpProfile_PlayRBTone2IP, IpProfile_EnableEarlyMedia, IpProfile_ProgressIndicator2IP, IpProfile_EnableEchoCanceller, IpProfile_CopyDest2RedirectNumber, IpProfile_MediaSecurityBehaviour, IpProfile_CallLimit, IpProfile_DisconnectOnBrokenConnection, IpProfile_FirstTxDtmfOption, IpProfile_SecondTxDtmfOption, IpProfile_RxDTMFOption, IpProfile_EnableHold, IpProfile_InputGain, IpProfile_VoiceVolume, IpProfile_AddIEInSetup, IpProfile_SBCExtensionCodersGroupID, IpProfile_MediaIPVersionPreference, IpProfile_TranscodingMode, IpProfile_SBCAllowedCodersGroupID, IpProfile_SBCAllowedCodersMode, IpProfile_SBCMediaSecurityBehaviour, IpProfile_SBCRFC2833Behavior, IpProfile_SBCAlternativeDTMFMethod, IpProfile_SBCAssertIdentity, IpProfile_AMDSensitivityParameterSuit, IpProfile_AMDSensitivityLevel, IpProfile_AMDMaxGreetingTime, IpProfile_AMDMaxPostSilenceGreetingTime, IpProfile_SBCDiversionMode, IpProfile_SBCHistoryInfoMode, IpProfile_EnableQSIGTunneling, IpProfile_SBCFaxCodersGroupID, IpProfile_SBCFaxBehavior, IpProfile_SBCFaxOfferMode, IpProfile_SBCFaxAnswerMode, IpProfile_SbcPrackMode, IpProfile_SBCSessionExpiresMode, IpProfile_SBCRemoteUpdateSupport, IpProfile_SBCRemoteReinviteSupport, IpProfile_SBCRemoteDelayedOfferSupport, IpProfile_SBCRemoteReferBehavior, IpProfile_SBCRemote3xxBehavior, IpProfile_SBCRemoteMultiple18xSupport, IpProfile_SBCRemoteEarlyMediaResponseType, IpProfile_SBCRemoteEarlyMediaSupport, IpProfile_EnableSymmetricMKI, IpProfile_MKISize, IpProfile_SBCEnforceMKISize, IpProfile_SBCRemoteEarlyMediaRTP, IpProfile_SBCRemoteSupportsRFC3960, IpProfile_SBCRemoteCanPlayRingback, IpProfile_EnableEarly183, IpProfile_EarlyAnswerTimeout, IpProfile_SBC2833DTMFPayloadType, IpProfile_SBCUserRegistrationTime, IpProfile_ResetSRTPStateUponRekey, IpProfile_AmdMode, IpProfile_SBCReliableHeldToneSource, IpProfile_SBCPlayHeldTone, IpProfile_SBCRemoteHoldFormat, IpProfile_GenerateSRTPKeys;
IpProfile 1 = "", 1, 0, 0, 10, 10, 46, 40, 0, 0, 0, 2, 2, 0, 0, 1, 0, -1, 1, 0, 0, -1, 0, 4, -1, 1, 1, 0, 0, "", -1, 0, 0, -1, 0, 0, 0, 0, 0, 0, 8, 300, 400, 0, 0, 0, -1, 0, 0, 1, 3, 0, 2, 2, 1, 0, 0, 1, 0, 1, 0, 0, 0, 0, 0, 1, 0, 0, 0, 0, 0, 0, 1, 0, 0, 0;

[ \IpProfile ]


[ CodersGroup0 ]

FORMAT CodersGroup0_Index = CodersGroup0_Name, CodersGroup0_pTime, CodersGroup0_rate, CodersGroup0_PayloadType, CodersGroup0_Sce;
CodersGroup0 0 = "g711Ulaw64k", 20, 0, -1, 0;
CodersGroup0 1 = "g711Alaw64k", 20, 0, -1, 0;

[ \CodersGroup0 ]


[ RoutingRuleGroups ]

FORMAT RoutingRuleGroups_Index = RoutingRuleGroups_LCREnable, RoutingRuleGroups_LCRAverageCallLength, RoutingRuleGroups_LCRDefaultCost;
RoutingRuleGroups 0 = 0, 1, 1;

[ \RoutingRuleGroups ]


[ ResourcePriorityNetworkDomains ]

FORMAT ResourcePriorityNetworkDomains_Index = ResourcePriorityNetworkDomains_Name, ResourcePriorityNetworkDomains_Ip2TelInterworking;
ResourcePriorityNetworkDomains 1 = "dsn", 1;
ResourcePriorityNetworkDomains 2 = "dod", 1;
ResourcePriorityNetworkDomains 3 = "drsn", 1;
ResourcePriorityNetworkDomains 5 = "uc", 1;
ResourcePriorityNetworkDomains 7 = "cuc", 1;

[ \ResourcePriorityNetworkDomains ]
</file>