~~Title: Digital~~
====== Digital DMG ======

====== DMG Configuration ======
  * You must first add the DMG to your network. By default the DMG is configured for IP address **10.12.13.74**.
  * Default username is **admin** and the default password is **IpodAdmin**.
  * Access to the DMG web administration may require the use of Internet Explorer with compatibility mode enabled.

The sections below correspond with the DMG menu items on the left of the configuration. Here you can see the default screen your presented with upon login.

{{:images:pbx:dmg:dmg1000-01.png?direct|}}

===== IP =====
Set the IP settings to match the network.

{{:images:pbx:dmg:dmg1000-02.png|?direct}}

===== Mgmt Protocols =====
All fields should remain as default shown here.

{{:images:pbx:dmg:dmg1000-03.png|?direct}}

===== Routing Table =====
All fields should remain as shown here.

{{:images:pbx:dmg:dmg1000-04.png|?direct}}

==== VoIP Host Groups ====
In order to route calls to the DuVoice system the IP address must be entered under VoIP Host 
Groups.

{{:images:pbx:dmg:dmg1000-04-1.png|?direct}}

  * **VoipGroup-1** \\ Enter the IP address of the DuVoice system.

===== TDM =====

==== Digital ====
Choose the Digital integration you wish to emulate.

{{:images:pbx:dmg:dmg1000-13.png|?direct}}

==== General ====

== TDM > General ==

{{:images:pbx:dmg:dmg1000-14.png|?direct}}

  * **Minimum Call Party Delay (ms)** \\ Set to 0.
  * **Maximum call Party Delay (ms)** \\ Set to 2000.

==== MWI Settings ====
Use these settings for either option one or two.

**Turn MWI On FAC and Turn MWI Off FAC**

=== Avaya Definity ===
  * You must leave these fields blank.
  * Avaya ACM/Definity enable Adjunct Supervision for each analog port for the 
DMG

=== Mitel ===
  * Set MWI values to:
    * TURN MWI On FAC to #21
    * TURN MWI Off FAC to #22
    * Enable COS Option 259 (Message Sending).
    * Enable COS Option 216 (Data Security).
  * Mitel dial tone - Enable System Option 22 (Last Party Clear: Dial Tone) for all 
analog Mitel ports connected to the DMG

=== Other PBX’s ===
Set the codes to match your PBX settings.
 
<callout type="info">
You must set your PBX to send a dial tone at disconnect or loop current drop.
</callout>

===== VOIP =====

==== General ====
All fields should remain as default shown here.

{{:images:pbx:dmg:dmg1000-09.png|?direct}}

==== Network Groups ====
All fields should remain as default shown here.

{{:images:pbx:dmg:dmg1000-10.png|}}

==== Media ====

{{:images:pbx:dmg:dmg1000-11.png|?direct}}

  * **Voice Activity Detection** \\ Set to off. Setting this value to off will reduce clipping during audio recordings on calls with low db levels.

==== Authentication ====
All fields should remain as default shown here.

{{:images:pbx:dmg:dmg1000-12.png|?direct}}

====== PBX Configuration ======

===== Avaya ACM/Definity =====
  * Enable Adjunct Supervision for each digital port connected to the DMG.

==== Station Programming ====
Digital set types must be set as 7434ND types

{{:images:pbx:dmg:dmg1000-15.png|?direct}}

On page two of the Digital extension for the DMG you must disable the **LWC reception** then enable the **LWC activation** and enable the **Display Client redirect**.

{{:images:pbx:dmg:dmg1000-16.png|}}

=== Button Programming ===
1: call-appr
2: call-appr
9: lwc-store
10: lwc-cancel

===== Meridian =====
For each of the ports connected to the DMG configure them as show below (LD 11).

^ TN ^ ^
| TYPE | 2616 |
| CDEN | 8D | 
| CUST | 0 |
| FDN | | 
| TGAR | 0 | 
| LDN | NO |
| NCOS | 7 | 
| RNPG | 0 | 
| SCI | 0 |
| SSU | | 
| CLS | FBD, WTA, MTD, FNA, HTA, ADD, HFD, MWA, CNDA, CPFD, CPTD |
| HUNT | XXXX |
| LHK | 0 | 
| KEY | 00 SCR YYYY (Call Appearance) \\ 07 PROGRAM \\ 13 MIK (Message Indication) \\ 14 MCK Message Cancellation) \\ 15 TRN (Transfer) |

====== DuVoice Configuration ======

Once the DuVoice software is installed you will be prompted to complete the setup wizard. Upon finishing the wizard, the DuVoice software will be configured for basic integration with the Dialogic Gateway.

==== PBX Template ====
Select the PBX Integration template

{{:images:pbx:dmg:dmg1000-17.png?direct|}}

==== MWI Method ====
MWI method should be set to SIP.

{{:images:pbx:dmg:dmg1000-18.png?direct|}}

==== PBX IP Address ====
Enter the IP address of the DMG as the PBX IP or DNS Name

{{:images:pbx:dmg:dmg1000-19.png?direct|}}

==== Port Numbering ====
Set the hunt group field to the hunt group number assigned to the DMG extensions.

{{:images:pbx:dmg:dmg1000-20.png?direct|}}