{{indexmenu_n>5}}
====== Install Dialogic for SIP ======

Dialogic PowerMedia (HMP) is the SIP stack provider used by DuVoice.  This sofware may be downloaded for free from the Dialogic web site.

==== Requirements ====
  * High Precision Event Timer (HPET) support.

==== Install Drivers ====
Run the Dialogic HMP installer and work through the install wizard as described below.

{{:images:vs7:manual:install-dialogichmp-1.png?nolink|}}

This page is informational only.  Click **Next*** to continue.

{{:images:vs7:manual:install-dialogichmp-2.png?nolink|}}

Click **Next** to accept the default install folder for program files and continue.

{{:images:vs7:manual:install-dialogichmp-3.png?nolink|}}

Click **Next** to accept the default install folder for data files and continue.

{{:images:vs7:manual:install-dialogichmp-4.png?nolink|}}

Check the //Core Runtime Package// option and the click **Next** to continue.

{{:images:vs7:manual:install-dialogichmp-5.png?nolink|}}

This page prompts you to accept installation of some 3rd-party software that the Dialogic software depends on.  Click **Yes** to continue.

{{:images:vs7:manual:install-dialogichmp-6.png?nolink|}}

Click **Next** to accept the default program folder.

{{:images:vs7:manual:install-dialogichmp-7.png?nolink|}}

This page reviews the selections you have made in the previous pages.  Click **Next** to continue.

{{:images:vs7:manual:install-dialogichmp-8.png?nolink|}}

The computer must be rebooted after the installer is finished, so select //**Yes, I want to restart my computer now**// and then click **Finish**.  The wizard will close and the computer will be rebooted.

==== Install License ====

Once the system has finished rebooting, run the //HMP License Manager// from the Start menu

{{:images:vs7:manual:install-dialogichmp-9.png?nolink|}}

----
=== Installing with license ports ===

1. Click **Browse**, as indicated in the figure below.

{{:images:vs7:manual:install-dialogichmp-9a.png?nolink|}}

2. Browse to the license file you downloaded from Dialogic or acquired from DuVoice. This .lic file should be placed in C:\OEM or C:\HMPLic, and new directory may need to be created.  Then click **OK**.

3. Click **Activate License**.

{{:images:vs7:manual:install-dialogichmp-9b.png?nolink|}}

4. Click **OK**.

{{:images:vs7:manual:install-dialogichmp-10.png?nolink|}}

----
=== Installing a single port or demo system ===
By default, the HMP installer provides a license for 1 port, so you can skip straight to the activation step:

1. Click **Activate License**.

{{:images:vs7:manual:install-dialogichmp-9b.png?nolink|}}

2. Click **OK**.

{{:images:vs7:manual:install-dialogichmp-10.png?nolink|}}

----
=== Configure Drivers ===

1. From the Start menu, run //Configuration Manager - DCM//.
2. Right-click on //HMP_Software #0 in slot 0/65535//.

{{:images:vs7:manual:install-dialogichmp-11.png?nolink|}}

3. Select //Restore device defaults//.

{{:images:vs7:manual:install-dialogichmp-12.png?nolink|}}

4.You will be prompted to confirm the choice to restore defaults; click Yes.

{{:images:vs7:manual:install-dialogichmp-13.png?nolink|}}

5. Select the License file that you activated in the previous step from the //Available Firmware// list, as shown below. Note that both the demo license and the active license will be displayed, make sure not to select the "1r1" demo license. Then click **OK**.

{{:images:vs7:manual:install-dialogichmp-9-1.png?nolink|}}

6. Double-click on //HMP_Software #0 in slot 0/65535// (the same entry you right-clicked in step 2).

7. Select the //Default IP Address// tab and verify the address.  It should be on the same subnet as your PBX.  Click **OK** when done.

{{:images:vs7:manual:install-dialogichmp-14.png?nolink|}}

8. From the main menu, select **Settings | System/Device autostart | Start System**.  This will automatically start Dialogic PowerMedia HMP when the computer is restarted.

{{:images:vs7:manual:install-dialogichmp-15.png?nolink|}}

9. Click the green arrow button on the toolbar to start Dialogic PowerMedia HMP.

{{:images:vs7:manual:install-dialogichmp-17.png?nolink|}}

10. If the drivers start, close the Configuration Manager.  If they don't, verify your HMP license and verify that your system supports the High Performance Timer (as noted on the [[vs7:manual:install:requirements|Requirements]] page).

{{:images:vs7:manual:install-dialogichmp-16.png?nolink|}}